Oil spills explained

What happens to oil at sea

A spill is not a stain that stays where it falls. It is carried by the water, pushed by the wind and changed by the sea itself. Understanding those forces is the first step to predicting where the oil will go.

Transport

Three forces move the slick

Ocean currents carry the oil with the water. Wind pushes the surface layer. Waves add a slow forward motion called Stokes drift. Move the sliders and watch the net drift change.

Schematic of the forces acting on an oil slick A slick at the center with three arrows for current, wind and waves, and a red arrow for the resulting drift. The arrows change as the sliders move. No net drift
  • Current
  • Wind effect (3% of wind speed)
  • Stokes drift
  • Net drift
Ocean current
Wind
Waves (Stokes drift)

Net drift

 

 

A teaching sketch, not model output. Here the net drift is simply the current plus 3% of the wind speed plus the Stokes drift. In STFM these terms are weighted and change in space and time, for every particle. Directions are where each force is heading, measured clockwise from north.

Fate

While it travels, the oil changes

Drift is only half of the story. From the moment it reaches the surface, oil is also being transformed. These four processes change how much oil is left, how thick it is and where it ends up. STFM follows each one for every particle.

Evaporation

The lighter fractions leave the slick for the air. It is usually the main early loss, and what remains is denser and more viscous.

Dissolution

A small share of the oil's soluble compounds dissolves into the water. The mass is small, but it matters for toxicity.

Emulsification

Seawater mixes into the oil and forms a thick water-in-oil emulsion, often called mousse. The slick grows in volume and gets harder to disperse.

Dispersion

Breaking waves tear the slick into droplets that mix down into the water column. Wave height is one of the inputs that sets how much oil goes under.

  1. Minutes to hoursGravity spreads the oil into a thin film. Evaporation starts at once.
  2. Hours to daysWind and waves work the surface. Emulsification and dispersion build up.
  3. Days to weeksWhat is left is heavier and changes more slowly. The Foz do Amazonas risk study judged coastal arrival within 30 days.

Typical order only. The pace depends on the type of oil, temperature and sea state, which is why the model needs to know the oil properties.

In practice

Questions STFM has already helped answer

Each case below is a published study. Follow the links for the full article.

2019–2020 · Northeast Brazil

How much oil was spilled?

An oil of unknown origin reached a large part of the Brazilian coast. Starting from the hypothesis of a slow leak from a tanker, the study used STFM to estimate an initial volume between 5,000 and 12,500 cubic metres.

Read the study
2019–2020 · Source areas

Where could it have come from?

Earlier time-reverse modeling pointed to several possible source areas. A probabilistic follow-up tested them with Monte Carlo simulations and a scenario tree to reduce the uncertainty.

Read the study
South Atlantic

Could it be oil dumped along shipping routes?

A later study uses STFM to ask whether the oil and tar balls that reach the coast may come from dumping along international shipping routes in the South Atlantic.

Read the study
Foz do Amazonas basin

How likely is it that oil reaches the coast?

47,500 probabilistic simulations from 95 drilling sites showed that the risk follows the seasonal migration of the Intertropical Convergence Zone.

Read the study

Prediction

Three questions, three kinds of run

Deterministic

Where did this spill go?

One release, one set of conditions, one trajectory. Best for reconstructing or forecasting a specific event.

Probabilistic

How likely is it to reach there?

Many runs under varied conditions, summed into a probability map of the areas the oil may reach. Best for planning and risk studies.

Time-reverse

Where could it have started?

Start from an observed slick and run the model backwards toward likely sources. Best for investigating an unknown origin.

How each mode works

Go further

See it for yourself

Read how the model is built, or set up SisMOM and run a simulation of your own.